Supply and Commissioning of Various Items for Pakistan Railways Carriage Factory Islamabad

Pakistan Railways Carriage Factory Islamabad invites bids through the E-Pak Acquisition and Disposal System (EPADS) for supply, installation, testing, and commissioning of various items from original manufacturers, authorized distributors, suppliers, and contractors registered with Income Tax & Sales Tax Departments and listed on the Active Taxpayers List of the Federal Board of Revenue. The procurement follows the Single Stage-One Envelope bidding procedure as per Public Procurement Rules 2004. Items being procured: - PVC Cables 24 items - M.S Sheets, Plates, SS Sheet etc. ~07 items - M.S Channels, equal angles etc. 14 items - M.S Channel, Angle CU3=05 items - Lube oil, Air filter etc = 15 items - PVC Cable accessories (adhesive tape, thimbles, ducts, conduit pipes) 26 items - Piano type switch, circuit breakers etc. 11 items - Air Diffuser = 02 items - Valve Regulated sealed lead Acid Battery=03 Items - Supply, installation, testing and commissioning of 11KV VCB 630Amp, 25-KA protection panel, Provision of HT Operating Rod (HOT Stick), Earthing rods with standard accessories - Electrical control Protection Device 01 item - Condenser fan motor, Evaporator Fan motor, heater Assembly etc = 10 items - Aluminum Composite Panel = 01 item - Glass Pane, Frosted Glass etc =12 items - Side Door holders, door stopper, tower bolts, glass holders etc. 17 items - Sliding door channel, sliding door mechanism, luggage rack, locking eye etc. 11 items - Aluminum Sections etc = 06 items - Side Wall Window Complete etc. =15 items - Roughing Grinding Disc, Abrasive cutting wheel, sanding discs, cutting discs, fabric grinding belt, rotary mounted points etc 18 items - High Speed Steel Machine Taps 12 items - Hand Tools, Power Tools, Electric Tools, Welding Tools, Measuring Tools, Hand Tools, Copper, Brass, Copper etc 11 items - Water Tiles, Finger Plates, Knife, Letter etc. 11 items - Hard Metal bars (3.05 Heavy duty) recycling all cocks, rivet hole machines etc. 11 items - Tungsten Carbide burrs spiral cut with chip breaker etc = 06 items - Round thread cutting dies, die holders, carbide tip, machine taps etc. 18 items - High Speed Twist Drills = 21 items - Twist drill made of High speed steel etc = 22 items - Centre drill H.S.S etc = 05 items - Carbide Tipped circular saw etc = 15 items - Power saw Blade made of high speed steel = 11 items - Single End mill cutter long series made of KHS-S etc = 18 items - Wet & Dry Paper, Seat Number set etc. 07 items - Repair, Replacement, commissioning, testing and successful operation of Butt Seam Welding Machine 01 Job - Welding Electrodes etc. 18 items - Oxygen gas in Liquid form - Plumbing items etc. 27 items - Carbon tetra chloride, hard drawn copper pipes, molded rubber flexible air duct etc. 12 items - Nitrogen gas = 01 item - GRP (Panels, Wall Board Assemblies, plates etc. 22 items - Packing REK = 02 items - Locking device, hinges etc = 16 items The scope covers supply and installation at the Carriage Factory site in Islamabad. Bidders must be registered with FBR and have relevant experience. Bid Security will be submitted before closing of tender through EPADS. Bidding documents with detailed terms and conditions can be downloaded free of cost from https://epads.gop.pk. Bids must be submitted on EPADS as per schedule. The tender closing date is **23 September 2026** with bid opening on the same day at 12:30 pm. Bidders are advised to carefully review the bidding documents and ensure timely submission through the EPADS portal. One practical tip is to verify all technical specifications and ensure compliance with PEC categories and FBR registration to avoid disqualification. For further details, contact the Assistant Controller of Purchase at Pakistan Railways Carriage Factory Islamabad.